New Q68 Case
- XorA
- Site Admin
- Posts: 1368
- Joined: Thu Jun 02, 2011 11:31 am
- Location: Shotts, North Lanarkshire, Scotland, UK
Re: New Q68 Case
This is very not vapourware BBQL network!
But do give us some time on the drivers, life is getting in the way!
But do give us some time on the drivers, life is getting in the way!
-
- Font of All Knowledge
- Posts: 3975
- Joined: Mon Dec 20, 2010 11:40 am
- Location: Sunny Runcorn, Cheshire, UK
Re: New Q68 Case
Looks great, I wil want one.
Can you start a new thread for this instead of corrupting this thread.
Can you start a new thread for this instead of corrupting this thread.
Last edited by Derek_Stewart on Sat Feb 18, 2023 9:59 pm, edited 1 time in total.
Regards,
Derek
Derek
Re: New Q68 Case
Apologies!Derek_Stewart wrote: ↑Sat Feb 18, 2023 9:32 pm Can you start a new thread for this ibstead of corrupting this thread.
-
- Font of All Knowledge
- Posts: 3975
- Joined: Mon Dec 20, 2010 11:40 am
- Location: Sunny Runcorn, Cheshire, UK
Re: New Q68 Case
A huge development like this, needs highlighting.ppe wrote: ↑Sat Feb 18, 2023 9:38 pmApologies!Derek_Stewart wrote: ↑Sat Feb 18, 2023 9:32 pm Can you start a new thread for this ibstead of corrupting this thread.
Regards,
Derek
Derek
Re: New Q68 Case
Are you aware of the termination issues? If you keep a termination inside the Q68 (so it can still at least be used as an endpoint without special adaptor) you will no longer be able to provide a dual connection. Also, just a normal Y-cable can not be used, because you need connectors with switches.Derek_Stewart wrote: ↑Sat Feb 18, 2023 6:23 pm I will make a standard 2 QL NET connector cable that will connect to the Q68 Rear Panel, this is mainly due lack of space on the Rear Panel.
-
- Font of All Knowledge
- Posts: 3975
- Joined: Mon Dec 20, 2010 11:40 am
- Location: Sunny Runcorn, Cheshire, UK
Re: New Q68 Case
Hi Peter,
The terminators will be outside the Q68 case, with the terminators in the supplied cable.
The terminators will be outside the Q68 case, with the terminators in the supplied cable.
Regards,
Derek
Derek
-
- Font of All Knowledge
- Posts: 3975
- Joined: Mon Dec 20, 2010 11:40 am
- Location: Sunny Runcorn, Cheshire, UK
Re: New Q68 Case
HI Peter,Peter wrote: ↑Sat Feb 18, 2023 10:20 pmAre you aware of the termination issues? If you keep a termination inside the Q68 (so it can still at least be used as an endpoint without special adaptor) you will no longer be able to provide a dual connection. Also, just a normal Y-cable can not be used, because you need connectors with switches.Derek_Stewart wrote: ↑Sat Feb 18, 2023 6:23 pm I will make a standard 2 QL NET connector cable that will connect to the Q68 Rear Panel, this is mainly due lack of space on the Rear Panel.
I simple solution to my problem would be to have the termination of te QL NET outside the Q68, with a Panel mounted JST connector to connect to the Q68 Expansion port, an ammended drawing to the Simple QL NET diagram is shown here:
Would this work?
My alternative solution was to drill 2 6mm dia. holes in the side of Q68 Case, which spoils the look of the case and I will have 60 holes to drill.
Regards,
Derek
Derek
Re: New Q68 Case
Yes. But it would take away the option to simply plug a network cable into the Q68. Which would otherwise be okay, if the Q68 is only used as an endpoint with fixed 330 Ohms termination (probably the majority of use cases).Derek_Stewart wrote: ↑Sun Feb 19, 2023 10:26 am I simple solution to my problem would be to have the termination of te QL NET outside the Q68, with a Panel mounted JST connector to connect to the Q68 Expansion port, an ammended drawing to the Simple QL NET diagram is shown here:QLNET-Q68_simple.jpg
Would this work?
Re: New Q68 Case
How? If there is only room for one jack at the Q68, and it is intended for direct plugin, it always has to be 330 Ohms terminated.