![Smile :)](./images/smilies/icon_e_smile.gif)
Hello from Nottinghamshire!
-
- RWAP Master
- Posts: 2839
- Joined: Sun Nov 28, 2010 4:51 pm
- Location: Stone, United Kingdom
- Contact:
Re: Hello from Nottinghamshire!
Yes the QL and ZX Spectrum (ZX Interface 1) use the same network lead - I have several for £2 each - you actually need 2 cables from memory to complete the circuit ![Smile :)](./images/smilies/icon_e_smile.gif)
![Smile :)](./images/smilies/icon_e_smile.gif)
Rich Mellor
RWAP Software
RWAP Adventures
SellMyRetro
Retro-Printer Module - add a USB printer to your QL
Also Involved in:
Icephorm
RWAP Software
RWAP Adventures
SellMyRetro
Retro-Printer Module - add a USB printer to your QL
Also Involved in:
Icephorm
Re: Hello from Nottinghamshire!
Nah. Don't do that. The QL network will cease to work if you connect the computers up in a circular manner - It needs to go point-to-point.RWAP wrote: - you actually need 2 cables from memory to complete the circuit
Sernet wants a circular connection, though.
Tobias
ʎɐqǝ ɯoɹɟ ǝq oʇ ƃuᴉoƃ ʇou sᴉ pɹɐoqʎǝʞ ʇxǝu ʎɯ 'ɹɐǝp ɥO
Re: Hello from Nottinghamshire!
A little late, but better late than never...
Welcome to the Forum!![Very Happy :D](./images/smilies/icon_e_biggrin.gif)
Welcome to the Forum!
![Very Happy :D](./images/smilies/icon_e_biggrin.gif)
--
If vanpeebles parps in the woods and there is nobody around, does it make a sound?
If vanpeebles parps in the woods and there is nobody around, does it make a sound?
-
- Aurora
- Posts: 933
- Joined: Sat Oct 25, 2014 9:53 am
Re: Hello from Nottinghamshire!
Yes, the two 'ends' of the QNet bus need to be left open-cct, to give the 130/2 = 65 ohm pull-down to the overall bus.
Though it'll probably still work - but less reliably (reflections?)
The page on the S*BASIC Manual online is incorrect in this regard and one of several items I was planning to submit to Norman for changing (under section A17 Networks).
Though it'll probably still work - but less reliably (reflections?)
The page on the S*BASIC Manual online is incorrect in this regard and one of several items I was planning to submit to Norman for changing (under section A17 Networks).
Re: Hello from Nottinghamshire!
Both of my QLs have now arrived and both have no video. I was going to send them to Ian Gledhill after a quick play, but that is now needed sooner rather than later. But at least they will then both work.
Re: Hello from Nottinghamshire!
I know this is a really noob question but.....
Can I get sound externally other than the inbuilt beeper?
Can I get sound externally other than the inbuilt beeper?
-
- RWAP Master
- Posts: 2839
- Joined: Sun Nov 28, 2010 4:51 pm
- Location: Stone, United Kingdom
- Contact:
Re: Hello from Nottinghamshire!
There were some add-on sound cards, but they are quite rare - QTALK was one, QSOUND the other - they were both based on the AY sound chip and used a special device driver.
The BEEP command is limited to the internal speaker - although you could turn it into an external speaker quite easily as the wires from the speak just push into a 2 pin header just behind the microdrive units
The BEEP command is limited to the internal speaker - although you could turn it into an external speaker quite easily as the wires from the speak just push into a 2 pin header just behind the microdrive units
Rich Mellor
RWAP Software
RWAP Adventures
SellMyRetro
Retro-Printer Module - add a USB printer to your QL
Also Involved in:
Icephorm
RWAP Software
RWAP Adventures
SellMyRetro
Retro-Printer Module - add a USB printer to your QL
Also Involved in:
Icephorm
Re: Hello from Nottinghamshire!
I've been mulling this over in the small hours. I'd like a mono socket out, like the Spectrum so I can play audio out and alter volume etc. If there's a 2 pin header for a speaker, it more than likely has the wrong current to connect straight to an amp.
So I Googled "speaker to RCA". There are loads of little converter boxes that appear to do the trick. Around £10 each. Their primary use is to provide a line out for a car stereo from the speakers output. They have 4 input wires to deal with stereo and then two rca output with a volume knob.
Anyone with any experience of this or an alternative?
So I Googled "speaker to RCA". There are loads of little converter boxes that appear to do the trick. Around £10 each. Their primary use is to provide a line out for a car stereo from the speakers output. They have 4 input wires to deal with stereo and then two rca output with a volume knob.
Anyone with any experience of this or an alternative?