Q68 netwrok port hardware

The Thor, Aurora, Q40, Q60 & Q68 etc. are discussed here.
FrancoisLanciault
Trump Card
Posts: 167
Joined: Mon Aug 08, 2011 11:08 pm

Re: Q68 netwrok port hardware

Post by FrancoisLanciault »

Hi,

I was finally able to fix my network board. I received the correct BAT-43 diode, installed it, but as many of you guessed, it did not solve the problem.

Then I realized the network signal would go high whenever I would plug my interface card. As a matter of fact, peek(hex(18020)) would give 57 as soon as the interface is plugged even if no cable is attached.

Removing the interface, I applied 3.3 volts to the 3v3in pin of the interface and I could measure 2.4 volts at the QL net pin. (Should be 0V or close to it because of the diode). Turn out I had a very dirty flux trace between 3v3in and QL net pin that was conducting a bit to much. A good cleaning solved the problem.

I now have my four QLs networked together !

- Q68
- SCG + Aurora
- GC + SD-QL
- BareBone QL 512k + TKII rom (latest arrival) now used to play games that are not compatible with the above systems.

The Q68 is now replacing the Aurora QL as my main developments machine.

Thank you every one for making this possible.

François


User avatar
Peter
QL Wafer Drive
Posts: 1949
Joined: Sat Jan 22, 2011 8:47 am

Re: Q68 netwrok port hardware

Post by Peter »

Hi François, glad to hear QLNET with the Q68 works for you now, thanks for the update!


Derek_Stewart
Font of All Knowledge
Posts: 3901
Joined: Mon Dec 20, 2010 11:40 am
Location: Sunny Runcorn, Cheshire, UK

Re: Q68 netwrok port hardware

Post by Derek_Stewart »

Hi,

Has anyone tried the Q68 QLAN connection to a Spectrum with Interface 1?


Regards,

Derek
User avatar
Peter
QL Wafer Drive
Posts: 1949
Joined: Sat Jan 22, 2011 8:47 am

Re: Q68 netwrok port hardware

Post by Peter »

Yes Detlef and others successfully did that at last years German QL meeting.


kmmann
ROM Dongle
Posts: 25
Joined: Mon Jun 29, 2015 6:30 pm
Location: Lincoln

Re: Q68 netwrok port hardware

Post by kmmann »

Derek_Stewart wrote:Hi,

I used Lumberg 3.5" Jack Connectors:
QLNET_Connector_Drawing.pdf
Lumberg_Jack connector.pdf
There needs to be a switch on the connector
Hi Derek

I see the lumberg jack connector you previously used are now not available. Can you suggest any alternatives?


User avatar
Dave
SandySuperQDave
Posts: 2765
Joined: Sat Jan 22, 2011 6:52 am
Location: Austin, TX
Contact:

Re: Q68 netwrok port hardware

Post by Dave »

This is all about the terminating resistor at the end of the network chain. It needs to be connected if no socket is present and disconnect if a socket is plugged in. The easiest solution to this if you have the wrong connectors is to make a single 3.5mm jack with the right terminating resistor across it.


Derek_Stewart
Font of All Knowledge
Posts: 3901
Joined: Mon Dec 20, 2010 11:40 am
Location: Sunny Runcorn, Cheshire, UK

Re: Q68 netwrok port hardware

Post by Derek_Stewart »

kmmann wrote:
Derek_Stewart wrote:Hi,

I used Lumberg 3.5" Jack Connectors:
QLNET_Connector_Drawing.pdf
Lumberg_Jack connector.pdf
There needs to be a switch on the connector
Hi Derek

I see the lumberg jack connector you previously used are now not available. Can you suggest any alternatives?
Hi,

I got some similiar on eBay, which I guess would imported from somewhere like Aliexpress.


Regards,

Derek
User avatar
bwinkel67
QL Wafer Drive
Posts: 1185
Joined: Thu Oct 03, 2019 2:09 am

Re: Q68 netwrok port hardware

Post by bwinkel67 »

I'm planning on creating the simple circuit and use the software to get my Q68 to talk to my QL. Anyone ever make a board for that?


Derek_Stewart
Font of All Knowledge
Posts: 3901
Joined: Mon Dec 20, 2010 11:40 am
Location: Sunny Runcorn, Cheshire, UK

Re: Q68 netwrok port hardware

Post by Derek_Stewart »

bwinkel67 wrote: Tue Feb 21, 2023 9:40 am I'm planning on creating the simple circuit and use the software to get my Q68 to talk to my QL. Anyone ever make a board for that?
When you say Q68 to QL what do you mean?

There is SerNET, QL NET all can provided server-client services and channel I/O, excute programs on the remote machine.


Regards,

Derek
User avatar
bwinkel67
QL Wafer Drive
Posts: 1185
Joined: Thu Oct 03, 2019 2:09 am

Re: Q68 netwrok port hardware

Post by bwinkel67 »

Derek_Stewart wrote: Tue Feb 21, 2023 10:24 am here is SerNET, QL NET all can provided server-client services and channel I/O, excute programs on the remote machine.
I was referring to this thread...i.e. QL Net


Post Reply