Hermes status
-
- Font of All Knowledge
- Posts: 3971
- Joined: Mon Dec 20, 2010 11:40 am
- Location: Sunny Runcorn, Cheshire, UK
Re: Hermes status
Hi,
I can programme the Hermes chips on a HiLo Systems All03a connected to a DOS based PC.
I also have an old Willems Programmer 3b PCB, but never tried it.
I can programme the Hermes chips on a HiLo Systems All03a connected to a DOS based PC.
I also have an old Willems Programmer 3b PCB, but never tried it.
Regards,
Derek
Derek
Re: Hermes status
'Twas not I, but mselkin seeking suitable programmer.martyn_hill wrote:Hi Silvester
On that point (another thing I delved into a while ago), I am going to build my own 8749 programmer working off a QL (equipped with lots of added hardware) in the next week or two. I also reckon it is possible to build an adaptor board for QEP III, which once the code is working OK I may implement. The only thing is it is possible to damage QEP III through bad programming (short programming voltage outputs to ground).
(edit: spelling correction of T'was)
David
-
- Font of All Knowledge
- Posts: 3971
- Joined: Mon Dec 20, 2010 11:40 am
- Location: Sunny Runcorn, Cheshire, UK
Re: Hermes status
HI,
There is another option, the Eprommer by Jan Bredenbeek, which is publically available, including the source code, at: https://github.com/janbredenbeek/EPROMmer
Just need a PCB layout, I was always going make one, I will do KiCad project for it.
There is another option, the Eprommer by Jan Bredenbeek, which is publically available, including the source code, at: https://github.com/janbredenbeek/EPROMmer
Just need a PCB layout, I was always going make one, I will do KiCad project for it.
Regards,
Derek
Derek
- mk79
- QL Wafer Drive
- Posts: 1349
- Joined: Sun Feb 02, 2014 10:54 am
- Location: Esslingen/Germany
- Contact:
Re: Hermes status
There is also https://www.kilgus.net/ql/eprommer-ii/. KiCad sources already included. But all must be heavily adapted for the 8749 to work.
Re: Hermes status
An 8749 adaptor board for QEP III could well work with other QL programmers (if IO and Vprog is similar). Easier than redesigning a new programmer from scratch. I had a close look at QEP III circuit and don't think it would take much to do, TBC.
Last edited by Silvester on Mon Sep 27, 2021 8:09 pm, edited 1 time in total.
David
-
- Font of All Knowledge
- Posts: 3971
- Joined: Mon Dec 20, 2010 11:40 am
- Location: Sunny Runcorn, Cheshire, UK
Re: Hermes status
Hi Marcel,
One minor point, do you not run an ERC check, ther looks to be many error flags, not serious, mainly flagging the not connected pins???
I am sorry I forgot about your Eprom Programmer, I will see if I can make some PCBs.mk79 wrote:There is also https://www.kilgus.net/ql/eprommer-ii/. KiCad sources already included. But all must be heavily adapted for the 8749 to work.
One minor point, do you not run an ERC check, ther looks to be many error flags, not serious, mainly flagging the not connected pins???
Regards,
Derek
Derek
- mk79
- QL Wafer Drive
- Posts: 1349
- Joined: Sun Feb 02, 2014 10:54 am
- Location: Esslingen/Germany
- Contact:
Re: Hermes status
For my own stuff, yes. But this is a straight Eagle import of a proven design that I offer for free, so probably didn't bother.Derek_Stewart wrote:One minor point, do you not run an ERC check, ther looks to be many error flags, not serious, mainly flagging the not connected pins???
Re: Hermes status
Thanks Prof and Derek for uploads.
Here is my take on the original IPC code. I haven't reviewed it yet so be interested to hear if anything doesn't seem correct.
Here is my take on the original IPC code. I haven't reviewed it yet so be interested to hear if anything doesn't seem correct.
- Attachments
-
- ipc_asm.zip
- (10.56 KiB) Downloaded 62 times
David
Re: Hermes status
Just to clarify Hermes is on 8749 but this code says "CPU: Intel 8049 (MCS-48 family)" so is Hermes on the 8049 as well?Pr0f wrote:ok - so this is incomplete - and may have inaccuricies in it - the idea would be to build upon it...
Oh! I guess the 80 is ROM and 87 is EEPROM.
The obvious path for a replacement seems to be the modern 8051 flash units but it might be easier to convert the code to 'C' for an upgrade that could be maintained by anyone.