Search found 3954 matches
- Tue Apr 16, 2024 9:41 pm
- Forum: Help for New Users
- Topic: QLTerminal v2.35 with TheOldNet WiFi v4
- Replies: 24
- Views: 528
Re: QLTerminal v2.35 with TheOldNet WiFi v4
Hi, It seems the QLTERM does not work in way I suggested, it sets the QL serial port speed to the same speed as the modem connect speed. The QLTerm manual says that the QL Baud Rate can be set in the terminal preferences, by pressing I So set the QL Baud Rate to 9600, Modem type buffered, serial por...
Re: PiStorm
Hi, Another solution would be to connect the Raspberry Pi to the QL data bus, so that the Raspberry Pi could be a co-processor to the QL. The main problem, is writing the device drivers, on the QL and maybe bare metal code on the Pi. Sort of like the BBC Tube interfacd for the QL, which maybe as rea...
- Tue Apr 16, 2024 8:44 pm
- Forum: Hardware
- Topic: Floppy problemsve.
- Replies: 4
- Views: 226
Re: Floppy problemsve.
Hi,
Maybe there is problems with the floppy disk cable connecting to the QL, if it is gge wrong way around, all the data lies lines will be grounded. Usually the Disk Drive LEDs are both on.
Check that the drives are correctly connected in the floopy disk case.
Maybe there is problems with the floppy disk cable connecting to the QL, if it is gge wrong way around, all the data lies lines will be grounded. Usually the Disk Drive LEDs are both on.
Check that the drives are correctly connected in the floopy disk case.
- Tue Apr 16, 2024 2:25 pm
- Forum: Help for New Users
- Topic: QLTerminal v2.35 with TheOldNet WiFi v4
- Replies: 24
- Views: 528
Re: QLTerminal v2.35 with TheOldNet WiFi v4
Hi, I think you're all getting the Serial port Baud rate confused with the Modem connect speed The serial port on the QL, usually SER2, should have it's Baud rate set to the highest reliable speed. Which could be 9600 Baud, using the BAUD command: BAUD 2,9600 This sets the data speed from computer t...
- Mon Apr 15, 2024 9:20 pm
- Forum: Hardware
- Topic: Q68 Advance Notice
- Replies: 78
- Views: 52405
- Mon Apr 15, 2024 7:23 am
- Forum: Compatibles Corner
- Topic: Thor XVI - Request for documentation...
- Replies: 9
- Views: 274
Re: Thor XVI - Request for documentation...
Hi Martyn,martyn_hill wrote: ↑Sun Apr 14, 2024 11:17 pm Just bumping this request for any info we might have about the Monitor pinout for the Thor XVI?
Look at Tony Firshman's web site, where he has information the Thor 1, which maybe be similar to the Thor IXV
http://tfs.firshman.co.uk/ql/ftp/qlgen/index.htm
Re: Q40/Q60
Hi,
I wonder if the video signal comming out of the VGA socket on thd Q60 board could be fed into a dedicated video processing circuit to changed the required sync signsls of the Q60 into the required signals for a modetn VGA monitor.
Which assume is what the OSSC does.
I wonder if the video signal comming out of the VGA socket on thd Q60 board could be fed into a dedicated video processing circuit to changed the required sync signsls of the Q60 into the required signals for a modetn VGA monitor.
Which assume is what the OSSC does.
Re: PiStorm
Blessed are the nay-sayers for the future is theirs! (Or is it?) In the mean time we wait for some test results from Derek. See where we go from there.. Sorry, a little delay, had some other problems to attend to. My house Electric circuit breakers kept on tripping. The fault was traced to Clothes ...
- Sat Apr 13, 2024 2:34 pm
- Forum: Help for New Users
- Topic: QLTerminal v2.35 with TheOldNet WiFi v4
- Replies: 24
- Views: 528
Re: QLTerminal v2.35 with TheOldNet WiFi v4
Hi,
If you can type AT and get OK back, the modem is connected to the computer correctly.
You can get information of the modem configuration and connections using the ATI command.
Type: ATIx where x = 0 to 3
i.e. AT0 or ATI1
The sparse manual says AT? gives list of the commands.
If you can type AT and get OK back, the modem is connected to the computer correctly.
You can get information of the modem configuration and connections using the ATI command.
Type: ATIx where x = 0 to 3
i.e. AT0 or ATI1
The sparse manual says AT? gives list of the commands.
- Sat Apr 13, 2024 9:27 am
- Forum: Help for New Users
- Topic: QLTerminal v2.35 with TheOldNet WiFi v4
- Replies: 24
- Views: 528
Re: QLTerminal v2.35 with TheOldNet WiFi v4
Hi,
Can you try switching off the local echo, with ATE0
Also try AT? for a list of the commands.
This is guesswork, as I do no have this modem.
Can you try switching off the local echo, with ATE0
Also try AT? for a list of the commands.
This is guesswork, as I do no have this modem.