Using ZX Microdrives on the QL
Re: Using ZX Microdrives on the QL
I put a photo with the Serial Number.
So It can help to solve the mistery?
So It can help to solve the mistery?
Re: Using ZX Microdrives on the QL
On further research, I found this which should nicely solve your problem: http://www.ebay.com/itm/Sinclair-ZX-Spe ... SwO~hXIJMl
Swapping wires 3 and 2 on the ribbon cable between the two boards should allow you to reverse the order of connection and use them ascending to the right. Solder side pin 4 is the pin that carries the location information, which is amended by the ULA. All the other pins pass through.
Check out this schematic
Swapping wires 3 and 2 on the ribbon cable between the two boards should allow you to reverse the order of connection and use them ascending to the right. Solder side pin 4 is the pin that carries the location information, which is amended by the ULA. All the other pins pass through.
Check out this schematic
Re: Using ZX Microdrives on the QL
Checked my ZX drives and found a slightly later one (if they were numbered sequentially):
Doesn't format or save unfortunately. Resistor values are r4=150/r5=180 as expected.Re: Using ZX Microdrives on the QL
Hi Charles, Simone,
Very interesting findings, I wish to fiddle with resistors as well, but I have only a single Speccy MD unit.
I was possibly close last year, when building `mPort', but again electronics I usually learn from you QL lads here.
Tomas
Very interesting findings, I wish to fiddle with resistors as well, but I have only a single Speccy MD unit.
I was possibly close last year, when building `mPort', but again electronics I usually learn from you QL lads here.
Tomas
-
- Font of All Knowledge
- Posts: 3932
- Joined: Mon Dec 20, 2010 11:40 am
- Location: Sunny Runcorn, Cheshire, UK
Re: Using ZX Microdrives on the QL
Hi,
I have 3 External ZX Microdrives, which came from a ZX Spectrums I purchased as a job lot.
" ZX MIcrodrives are joined with the plastic plate and expansion connector, each drive has a Serial Number of:
04-082935
04-081725
And a Single ZX Microdrive with a serial number of:
T-I12961
Does anyone know if the serial number has a bearing on QL compatibility.
I was going to remove the microdrive and install a QL-SD card, placing the unit on the top QL over the internal microdrives.
I have 3 External ZX Microdrives, which came from a ZX Spectrums I purchased as a job lot.
" ZX MIcrodrives are joined with the plastic plate and expansion connector, each drive has a Serial Number of:
04-082935
04-081725
And a Single ZX Microdrive with a serial number of:
T-I12961
Does anyone know if the serial number has a bearing on QL compatibility.
I was going to remove the microdrive and install a QL-SD card, placing the unit on the top QL over the internal microdrives.
Regards,
Derek
Derek
-
- Font of All Knowledge
- Posts: 3932
- Joined: Mon Dec 20, 2010 11:40 am
- Location: Sunny Runcorn, Cheshire, UK
Re: Using ZX Microdrives on the QL
Hi Dave,Dave wrote:On further research, I found this which should nicely solve your problem: http://www.ebay.com/itm/Sinclair-ZX-Spe ... SwO~hXIJMl
Swapping wires 3 and 2 on the ribbon cable between the two boards should allow you to reverse the order of connection and use them ascending to the right. Solder side pin 4 is the pin that carries the location information, which is amended by the ULA. All the other pins pass through.
Check out this schematic
Could a jumper be installed so that the microdrive could be configurable as MDV3 or MDV4
I will have a look on at this on my dual ZX Microdrive units.
But how many external MDVs can be supported on the EC1 external Microdrive expansion interface on the QL?
Regards,
Derek
Derek
- XorA
- Site Admin
- Posts: 1359
- Joined: Thu Jun 02, 2011 11:31 am
- Location: Shotts, North Lanarkshire, Scotland, UK
Re: Using ZX Microdrives on the QL
What tolerance are the resistors? If they were 10% tolerance ones which Ive found in a few 80s devices thats actually quite a wide range of values.Doesn't format or save unfortunately. Resistor values are r4=150/r5=180 as expected.
Even 5% is pretty wide!
G
Re: Using ZX Microdrives on the QL
Hi Derek,
Mine is 07-127762, not sure what resistors values it has. does not format QL attached.
Tomas
Mine is 07-127762, not sure what resistors values it has. does not format QL attached.
Tomas
Re: Using ZX Microdrives on the QL
So a unit that format and write correctly is very rare.tcat wrote:Hi Derek,
Mine is 07-127762, not sure what resistors values it has. does not format QL attached.
Tomas
Ehm...I think that this Speccy unit was one from QL mounted on the case of the ZX one...
Re: Using ZX Microdrives on the QL
While the PCBs are very different between the Speccy and QL the schematics are functionally identical. Unless the Speccy and QL devices use different ULAs, the resister values and possibly head resistances might be the only differences.
In theory, the Spectrum can support 8 microdrives, and the QL already having 2 could support 6 more.
In theory, the Spectrum can support 8 microdrives, and the QL already having 2 could support 6 more.